| GERBER GOLD ROUTING BITS |
| |
Gerber Gold routing bits are designed for greater performance and longer tool life. These remarkable routing bits are made from the highest quality micrograin carbide to the tightest tolerances in the industry. They are then coated with titanium nitride to enhance their durability even further. The result is superior edge quality and lower tooling cost. These high performance bits can be used with all Gerber routers/engravers, as well as with other routers, both automated and manual.
Email us for information - click
here -
|
|
|
| TWO-FLUTE SPIRAL BITS: |
| These are the most versatile type of bits
and are used for general routing of the
following materials: |
-
Harder Materials: Such as plate aluminum,
brass, bronze, copper; cast acrylics, solid
surface materials, particle board, plywood, and
hardwoods.
- Softer Materials: Such as foam boards,
engraving stock, PVC (Sintra®, Komatex, Trovicel®,
Celtec, etc.) soft plastics, soft woods, and
similar density materials.
|
| These bits provide excellent chip removal
from the cut because of the upward spiral
action. They also assure excellent edge quality
on these materials. |
| |
| Part No. English |
Shank Diameter |
Cutting Diameter |
Cutting Edge Length |
Part No. Metric |
Shank Diameter |
Cutting Diameter |
Cutting Edge Length |
| P50521B |
1/8" |
1/16" |
3/16" |
P52262B |
3mm |
1.6mm |
4.5mm |
| P50525B |
1/8" |
1/8" |
1/4" |
P50903B |
3mm |
3mm |
6mm |
| P50522B |
1/8" |
1/8" |
1/2" |
P50902B |
3mm |
3mm |
12mm |
| P50526B |
1/4" |
3/16" |
3/8" |
P52260B |
6mm |
4.5mm |
9.5mm |
| P50523B |
1/4" |
3/16" |
5/8" |
P52261B |
6mm |
4.5mm |
16mm |
| P50528B |
1/4" |
3/16" |
1
1/8" |
P52259B |
6mm |
4.5mm |
30mm |
| P50527B |
1/4" |
1/4" |
1/2" |
P50900B |
6mm |
6mm |
12mm |
| P50524B |
1/4" |
1/4" |
3/4" |
P50901B |
6mm |
6mm |
19mm |
| P50529B |
1/4" |
1/4" |
1 1/2" |
P52365B |
6mm |
6mm |
40mm |
| P50530B |
1/4" |
1/4" |
2 1/4" |
P52258B |
6mm |
6mm |
55mm |
| P52819B |
1/8" |
1/8" |
1 1/4" |
|
|
|
|
|
|
|
|
SINGLE-FLUTE RADIAL BITS |
 These
bits are ideal for cutting sheet aluminum and
brass with a thickness of .060" (1.5mm) and
less, as well as soft woods and soft alloy
aluminum. |
|
Unlike the spiral flute bits, these bits have a
single straight cutting edge which doesn’t pull
up on the work piece. This straight flute allows
the bit to “shear" the chip off at the top edge
of the material being cut without leaving a
burr. The chip extraction, however, will not be
as good as a spiral bit. |
|
|
| Part No. English |
Shank Diameter |
Cutting Diameter |
Cutting Edge Length |
|
Part No. Metric |
Shank Diameter |
Cutting Diameter |
Cutting Edge Length |
| P50532B |
1/4" |
1/8" |
1/2" |
P52256B |
6mm |
3mm |
12mm |
| P50533B |
1/4" |
3/16" |
5/8" |
P52255B |
6mm |
4.5mm |
16mm |
| P50534B |
1/4" |
1/4" |
3/4" |
P52254B |
6mm |
6mm |
19mm |
| P50535B |
1/4" |
1/4" |
1 1/2" |
P52253B |
6mm |
6mm |
40mm |
|
| |
| THREE-FLUTE SPIRAL TAPERED BITS |
 These
bits can be used on all materials listed for the
two-flute spiral bits. The difference is that
the tapered bits give you an angle on the edge
of the material being cut. As a result, these
bits are excellent for cutting vacuum form
molds. |
| Also, when you want something other than a
straight edge for special applications, these
bits can be used to create a "halo" effect
without adding any additional cost. |
| |
| Part No. English |
Shank Diameter |
Cutting Diameter |
Cutting Edge Length |
° |
|
Part No. Metric |
Shank Diameter |
Cutting Diameter |
Cutting Edge Length |
° |
| P50531B |
1/4" |
1/8" |
1/2" |
7° |
P52257B |
6mm |
3mm |
12mm |
7° |
| P50643B |
1/4" |
1/8" |
1 |
3° |
P52252B |
6mm |
3mm |
25mm |
3° |
|
| |
